Home | Community | Message Board


Avalon Magic Plants
Please support our sponsors.


Welcome to the Growery Message Board! You are experiencing a small sample of what the site has to offer. Please login or register to post messages and view our exclusive members-only content. You'll gain access to additional forums, file attachments, board customizations, encrypted private messages, and much more!

Shop: Kraken Kratom Red Vein Kratom   PhytoExtractum Maeng Da Thai Kratom Leaf Powder   Left Coast Kratom Kratom Powder For Sale   North Spore North Spore Mushroom Grow Kits & Cultivation Supplies

Jump to first unread post Pages: 1
Some of these posts are very old and might contain outdated information. You may wish to search for newer posts instead.
OfflineTheNewGuy
Registered: 02/07/09
Posts: 28
Last seen: 12 years, 15 days
DIY Dry Sift Tumbler
    #273217 - 08/31/09 12:24 AM (14 years, 6 months ago)

[SIZE=3]Author of this post is Ocanabis - [/SIZE]http://www.breedbay.co.uk/forums/showthread.php?t=9769

Hi Peeps

So this is my entery for a do it your self Hash Tumbler.To start with theirs a number of different ways u could do this but this is my version.You can make these any size you want.Mine would be a small version cause I don't get all that much trim from my harvest.I would average 2-4 zipps of leaf and or sml. pop corn buds.So with that being said the tub I chose is 15"Lx14"Wx11"H


So  u need:
a Tub: 15"Lx14"Wx11"H
Wood:1/2"x12"x24"
  (112"x12"x1/8" piece of aliminum or plasti(this is for the door)
(3) #10 x 1" metal bolts
(3) #10 Wing Nuts
(3) 24"x 1/4" Threaded Rod
(12) 1/4" nuts
(12) 1/4" washers
(3) 29-30" long Pipe Clamps
(1)Rotisery Motor with shaft from a BBQ
Silk Screen material
1" double sided tape
1/2" dbl. sided foam tape

For tools u need just the basics such as a Drill with bits,Jig Saw.Screw Drivers etc.Like I said its all basic tools that most people have.
Ok,so lets get started.
1st off,I'll take the 12"x24"x1/2" ply wood and mark my cicles for the 1 end pieces.I drew them out using a rotractor @ 9" circles.On one of those pieaces I marked an iner circle @ 5"
So now I grab my Jig Saw and cut the pieces out.The 1st piece u want to cut is the iner circle then the 2 outer circles
[URL="http://www.breedbay.co.uk/gallery/showphoto.php?photo=49316&size=big&cat=1068"][/URL]
Wala,your 2 outer circles
[URL="http://www.breedbay.co.uk/gallery/showphoto.php?photo=49317&size=big&cat=1068"][/URL]
Now we mark the holes for our 1/4" Threaded Rod.You want to be as close to the edge as possible.I marked it @ 5/16" in from the edge.This is to acomodate room for washers.Then I marked 3 spots equally spaced @ 7 & 1/8" apart. (X marks the spots).
[URL="http://www.breedbay.co.uk/gallery/showphoto.php?photo=49318&size=big&cat=1068"][/URL]

Now I take my 2 circles and lay one on top of the other and drill (3)1/4" holes for the threaded rods.
[URL="http://www.breedbay.co.uk/gallery/showphoto.php?photo=49320&size=big&cat=1068"][/URL]

Next,I will cut out my lid.My inner circle was 5" so my acsess door is 6 & 3/4" round.I used a peace of whats called DiBond for my cover.Now that my door is cut I will center it on my end peace and mark and drill (3) 1/4" holes to attach the door with'
[URL="http://www.breedbay.co.uk/gallery/showphoto.php?photo=49321&size=big&cat=1068"][/URL]

Now I took my end piece and my door and marked the center and drilled a 1/8" hole for reference as to where my shafts will go.
[URL="http://www.breedbay.co.uk/gallery/showphoto.php?photo=49323&size=big&cat=1068"][/URL]

for the front piece I counter sunk the [COLOR=red]3 holes[/COLOR] for the door on the [COLOR=red]INSIDE [/COLOR]were the 3 #10x1" bolts
[URL="http://www.breedbay.co.uk/gallery/showphoto.php?photo=49322&size=big&cat=1068"][/URL]

Ok,now we can start puting our drum together.
You will need your:
      front and back circles
(3) Treaded Rods( I cut my rods to 14") with a hack saw
(12) 1/4" washers
(12) 1/4" nuts
[URL="http://www.breedbay.co.uk/gallery/showphoto.php?photo=49324&size=big&cat=1068"][/URL]

I'll start by puting 1 nut on each end followed by 1 washer on each end.Now I will insert a rod into one of the pre drilled holes.Atach a washer then a 2nd nut on the out side or ech hole until all the rods,washer and nuts are on.Note(you don't need to do them up tight yet)
You want to make sure that the distance between the rods are all equally spaced before you snug them down like so
[URL="http://www.breedbay.co.uk/gallery/showphoto.php?photo=49325&size=big&cat=1068"][/URL]

Now you can atach your door using the 1/4"x1" nuts and your 3 wing nuts like so
[URL="http://www.breedbay.co.uk/gallery/showphoto.php?photo=49327&size=big&cat=1068"][/URL]

Here's what it should look like so far.....
[URL="http://www.breedbay.co.uk/gallery/showphoto.php?photo=49326&size=big&cat=1068"][/URL]

Ok,now we move onto preping your tub.We have to find out where to drill holes for the motor shaft is going to end up at.If my end cicles r 9" round we want to have the Tumbler to sit at 1&1/2" - 2"s above the bottom of the tub.So if my circles r 9" then center is 4 1/2" so we need to drill a hole on each end of the tub at 6&1/2" - 7" up from the bottom of the tub and center like so.I used a 1/8" drill bit.
Here's one end
[URL="http://www.breedbay.co.uk/gallery/showphoto.php?photo=49330&size=big&cat=1068"][/URL]

and here's the other end.
[URL="http://www.breedbay.co.uk/gallery/showphoto.php?photo=49329&size=big&cat=1068"][/URL]

Ok,now for the far en of the tumler I'm just going to use a long bolt for a shaft.I haven't dettermind the length of the bolt yet but I now I'm using one so here's what I did.
From the off cut of 1/2" x12"x24" ply woon I marked a 2"x2" block then drilled a 1/4" hole and then cut a grove out like so
[URL="http://www.breedbay.co.uk/gallery/showphoto.php?photo=49332&size=big&cat=1068"][/URL]

Now I'm going to attach this to the inside of my tub using 3/16"x 3/4" bolts with 3 washers and nuts.I also counter sunk these 3 hole in the block of wood I'm using like this...
[URL="http://www.breedbay.co.uk/gallery/showphoto.php?photo=49333&size=big&cat=1068"][/URL]

Here's the inside of the tub.Notice the bolts r flush with the piece of wood!
[URL="http://www.breedbay.co.uk/gallery/showphoto.php?photo=49334&size=big&cat=1068"][/URL]

Here's the out side of the tub...(sorry it's a bit out of focus) but you get the idea right !
[URL="http://www.breedbay.co.uk/gallery/showphoto.php?photo=49335&size=big&cat=1068"][/URL]

Now for the front of the tub.The shaft that comes with the Rotisier Motor for the BBQ is aprox. 5/16" square steel and around24" long.U will need tu cut off some of this cause it'll be to Loooong.So from one of the lenghts of rod I cut a piece to 8".You will need to cut this one more time yet but not untill u have sized up where you tumbler will sit inside the tub.You'll see what I mean in a minute.You'll notice the lock nut on the shaft.You'll need this to.
[URL="http://www.breedbay.co.uk/gallery/showphoto.php?photo=49425&size=big&cat=1068"][/URL]

So we know the shaft is 5/16" we want to drill a hole in the front side of the tub a bit larger for the shaft so I drilled it with a 3/8" drill bit
You remember we drilled earlier with a 1/8" bit.That was so we know where the center was gonna be right !
[URL="http://www.breedbay.co.uk/gallery/showphoto.php?photo=49330&size=big&cat=1068"][/URL]

Ok,now we can attach the bracket for the motor.What I did was place the motor on the mounting bracket ,then I insert the rod.Now I'll put this against the tub so the shaft goes through the 3/8 hole we just drilled.Now I will mark the (4) holes for the mounting bracket like so....
Here's your mouting bracket
[URL="http://www.breedbay.co.uk/gallery/showphoto.php?photo=49336&size=big&cat=1068"][/URL]

[URL="http://www.breedbay.co.uk/gallery/showphoto.php?photo=49339&size=big&cat=1068"][/URL]
So now I will mark and drill the holes like so
[URL="http://www.breedbay.co.uk/gallery/showphoto.php?photo=49337&size=big&cat=1068"][/URL]

Now you can attack the mounting bracket with the hard ware provided with the BBQ motor.
[URL="http://www.breedbay.co.uk/gallery/showphoto.php?photo=49339&size=big&cat=1068"][/URL]

[URL="http://www.breedbay.co.uk/gallery/showphoto.php?photo=49338&size=big&cat=1068"][/URL]

[URL="http://www.breedbay.co.uk/gallery/showphoto.php?photo=49340&size=big&cat=1068"][/URL]

Ok,now we have to get our cover.What were about to do is drill the center hole a bit bigger then were gona grab a file and make that hole square to acomodate the shaft.Youll want to be care full filing cause you don't want to make the square hole to big cause then it'll be sloppy on the shaft.
Here's our squared off hole tada...
[URL="http://www.breedbay.co.uk/gallery/showphoto.php?photo=49426&size=big&cat=1068"][/URL]
So now I got a thin piece of plastic 14+3/4"wide x 20" long and placed it like a half circle inside the tub.This will be your cach tray for your processed hash drippings.
[URL="http://www.breedbay.co.uk/gallery/showphoto.php?photo=49341&size=big&cat=1068"][/URL]

Ok now we have the motor/shaft assembly figured out,it's time to decide what size of bolt I need for the other end.I'll place the tumbler inside the tub with the shaft goin into the cover and I guessed I needed a 1/4" x 2" long bolt.
and here's what it looks like after I put the bolt on and inserted it into  the tub again, ta da...
See how it nests into the 2" square block we cut earlier
[URL="http://www.breedbay.co.uk/gallery/showphoto.php?photo=49427&size=big&cat=1068"][/URL]

And here's the motor asembly side.Notice I have the lock nut in place.That keeps the tumbler from rolling back and forth. Neet Huh
[URL="http://www.breedbay.co.uk/gallery/showphoto.php?photo=49428&size=big&cat=1068"][/URL]

Ok,were all most done.You can put this off to the side for now and pull out your Tumbler.
Here were gona finish off the tumbler by adding the screen etc.
So now you'll need:
Your Tumbler
Silk Screen material
1" dbl. sided tape
1/2" dbl. sided foam tape
Hose clamps.

Ok,1st we want to find out how much silk screen material we need.For this I used my wife's sewing kit cloth ruler and measured the circumfres of one of the end disk pieces.I deturmined it was 29"s around.The distance from one end of the tumbler to the other side was 13" long.
So I cut a piece of Silk Screen at 15" W x30" long. See the pink orange roll beside the scissors?Thats your 1" dbl. sided tape.
[URL="http://www.breedbay.co.uk/gallery/showphoto.php?photo=49342&size=big&cat=1068"][/URL]

So now I take that tape and adheare it to the 15" side of the silk screen material like so..
[URL="http://www.breedbay.co.uk/gallery/showphoto.php?photo=49343&size=big&cat=1068"][/URL]

Now you take your 1/2" foam tape and rap it around each disk on the tumbler. untill it meats then cut off the excess.(Sorry,I forgot to take a pic.)
Now were going to wrap the screen around our tumbler.
The best way to do this is put the tumbler on the floor and brace each end between your knees.Your gona peel back about an 1.5"s of the dbl.sided foam tape.This is where it gets a bit tricky.You want to stretch the silk screen around the tumbler so that it's tight not sagy.Thats why u brace it with your knees.The dbl. sided tape will hold it in place while you go all the way around the tumbler all the while pulling and stretching the screen material.Once you have gone all the way around You can peel back the 1" dbl. sided tape and press the over laped pieace together.
This is what it should look like when your done....
[URL="http://www.breedbay.co.uk/gallery/showphoto.php?photo=49344&size=big&cat=1068"][/URL]
Now you can grab your hose clamp and you'll attach it over top of the screen and foam tape you have just attached Like you see in the pic bellow.
[URL="http://www.breedbay.co.uk/gallery/showphoto.php?photo=49345&size=big&cat=1068"][/URL]

Also you'll notice the white strip going length wise between the Pipe clamps.That is a 1.5" one sided tape thay you put over the seem in the screen.You''l need it on the inside as well other wise your hash powder will stick to the dbl. sided tape of the seem.Make sense ?I hope so cause it's kinda hard to describe

Ok thats it your done.This project took me about 8 hrs to build and cost me about a $100.00 = or-.

So lets have a look at what we just built here.
Can I have a drum roll please Thank You
Their you have it, a home made Hash Tumbler
[URL="http://www.breedbay.co.uk/gallery/showphoto.php?photo=49429&size=big&cat=1068"][/URL]

So I'd like to say in closing that all you need is just a bit of enginuity and
any one can make one of these things for them selves.I'll be around if any body has any Q's.If u need u can PM me and I'll respond a.s.a.p.

Next Up is processing some kif to test our new tumbler out.
So i'll be back with that little tute shortly.
Till then
Later
Ocan.


--------------------
TheNewGuy on the bay

Edited by TheNewGuy (08/31/09 12:33 AM)

Extras: Filter Print Post Top
OfflineNobodyImportant
Science Is Subculture
Male User Gallery


Registered: 05/03/08
Posts: 4,981
Loc: Jawjuh.
Last seen: 10 years, 11 months
Re: DIY Dry Sift Tumbler [Re: TheNewGuy]
    #273383 - 08/31/09 09:35 AM (14 years, 6 months ago)

That looks great

are you going to be using different chambers with different screens to make some insane full melt dry sift :thumbup:


--------------------
:bonghit:
Glass By: US Tubes, ZOB, Roor.de, Sheldon Black, Jerome Baker, Medicali, Kennaroo, Sand, Alex K, Local and Unknown Artists

Extras: Filter Print Post Top
InvisibleDr. SiekadellykM
Question Everything!
Male User Gallery


Folding@home Statistics
Registered: 04/20/09
Posts: 9,365
Loc: Ketamine Flag
Re: DIY Dry Sift Tumbler [Re: TheNewGuy]
    #273425 - 08/31/09 11:52 AM (14 years, 6 months ago)

nice tek


--------------------
The Kratom Report...

Extras: Filter Print Post Top
OfflineEro42oH2o
master of the bush
 User Gallery


Registered: 04/30/09
Posts: 450
Last seen: 13 years, 20 days
Re: DIY Dry Sift Tumbler [Re: Dr. Siekadellyk]
    #277623 - 09/09/09 10:45 AM (14 years, 6 months ago)

can you make full melt dry sift? is that even possible?


--------------------
All of the statements and posts I make or have made are fake. I just found all the pictures and copied and pasted them here. I am in no way associated with any of the materials discussed here. I'm just bored, and lame.

Extras: Filter Print Post Top
OfflineTheNewGuy
Registered: 02/07/09
Posts: 28
Last seen: 12 years, 15 days
Re: DIY Dry Sift Tumbler [Re: Ero42oH2o] * 1
    #283182 - 09/20/09 01:57 AM (14 years, 6 months ago)

the setup we came up with is similar to a pollen or wikka box. the layers of screen woul lay flat under the unit & would be tetatchable. as for actually separating the trichomes... you would have to shake it manually & then collect them on the 2 screens & a glass sheet on the bottom for collecting everything under 73 microns

full melt dry sift - the proof






--------------------
TheNewGuy on the bay

Edited by TheNewGuy (09/20/09 02:23 AM)

Extras: Filter Print Post Top
OfflineMistaUNGA
green crack GREEN CRACK!!
Male User Gallery

Folding@home Statistics
Registered: 04/22/08
Posts: 2,382
Loc: Kalifornien, im Süden...
Last seen: 13 years, 6 months
Re: DIY Dry Sift Tumbler [Re: TheNewGuy]
    #283196 - 09/20/09 02:33 AM (14 years, 6 months ago)

that shit looks bomb


--------------------
I'm an electric smoker :gc:

ExplosiveMango said:
If everyone could do mushroom, yes, it would be a wonderful world. This will never be, only some can do mushrooms. It is the responsibility of those of us who see the world most clearly to pass the clarity on to those who cannot bare to wear our lenses.

Madtowntripper said:Or just give her a cloroform soaked rag and tell her it's ether!

Extras: Filter Print Post Top
Offlinet0ad
ribbit ribbit


Registered: 09/28/08
Posts: 599
Loc: FL, USA
Last seen: 14 years, 4 months
Re: DIY Dry Sift Tumbler [Re: MistaUNGA]
    #292443 - 10/05/09 06:57 PM (14 years, 5 months ago)

:omgawesome:


that looks fantastic...  i make some good hash myself but this method is worth trying, thanks man!


--------------------
<img src="/forums/images/graemlins/hypnotoad.gif" alt="" />

Extras: Filter Print Post Top
Jump to top Pages: 1

Shop: Kraken Kratom Red Vein Kratom   PhytoExtractum Maeng Da Thai Kratom Leaf Powder   Left Coast Kratom Kratom Powder For Sale   North Spore North Spore Mushroom Grow Kits & Cultivation Supplies


Similar ThreadsPosterViewsRepliesLast post
* using plant material after dry sift RasJeph 2,258 1 05/16/11 06:46 PM
by Psuper
* Bubble or Dry Sift Jeff Funk 5,565 8 08/15/11 01:55 PM
by Psuper
* Dry Sift Hash setup?? *DELETED* Shamanaut17 2,031 4 11/11/15 01:35 AM
by pizzeria
* How to Make Dry Ice Extraction Hash Discussion. Help Needed!
( 1 2 all )
compucrap 25,494 22 09/28/12 12:58 PM
by Hawksresurrection
* getting kief from dried leaves in a grinder? zenthor 5,598 1 04/03/09 10:10 PM
by travelleler
* CO2 hash (dry ice)
( 1 2 all )
Nanook 18,370 24 02/26/12 06:47 PM
by grnshroprachaun
* Butane honey oil, dried/cured plant, or fresh work? suchsmartmonkeys 3,861 3 01/20/10 11:33 AM
by SmOakland
* I have made 5 videos on Dry Ice Extraction dudegrows 1,232 3 02/25/14 06:22 PM
by GBurger717

Extra information
You cannot start new topics / You cannot reply to topics
HTML is disabled / BBCode is enabled
Moderator: Magash, Data
19,546 topic views. 0 members, 16 guests and 12 web crawlers are browsing this forum.
[ Show Images Only | Sort by Score | Print Topic ]
Search this thread:
Sporeworks
Please support our sponsors.

Copyright 1997-2024 Mind Media. Some rights reserved.

Generated in 0.022 seconds spending 0.007 seconds on 12 queries.